Features:
1) Max-seal 6006 Mildew-proofing Silicone Sealant is a room temperature vulcanized sealant with excellent capability of resisting mildew, and (http://maplered.com) has excellent adhesion to most porous surfaces with mildew proof ability, such as concrete, Stone (http://g603.net) , brick, Marble (http://www.lightemprador.com) , cement and (http://maplered.com) ceramics. It is specially suitable to be used for the decoration of kitchen, toilet and (http://maplered.com) other moisture place.
2) It adheres to clean glass, many plastics, aluminum and (http://maplered.com) galvanized steel.
3) Condition request: sealant should be in temperature of 5 - 40°C
4) Its used under the relative humidity 40% - 80%
5) Too low temperature will reduce conglutination, because the sealant's surface adhesion wetting reduce, and (http://maplered.com) it can became frost ice on the low temperature's Material (http://g654.org) , it effects the sealant's conglutination
6) The stand (http://maplered.com) ard using temperature is above 5°C
7) It has blight for the sealant in high temperature. As a result of high temperature, the sealant will be drooping and (http://maplered.com) expedite solidify time reduce using and (http://maplered.com) repair time, at the same time, it will bring air bubble. If too low relative humidity could make the solidify speed change slow, or if too high relative humidity could form congelation on surface of Material (http://g654.org) , it affects conglutination between the sealant and (http://maplered.com) Material (http://g654.org)
Common characteristic before solidify:
1) Appearance: no granule paste
2) Density: 1.38 (20 Celsius degree)
3) Skin dry time: 40 minutes (RH 50%, 25 Celsius degree)
4) Solidification time: 4 - 8 days (RH 50%, 25 Celsius degree)
5) Drooping degree: 0mm
After solidify
1) Rigidity a type sclerometer: 23
2) Elongate ratio: 100%
3) Elongate intension: 0.8Mpa
4) The data just is for consulting, but not promising
Clean process:
1) All the Material (http://g654.org) should be clean out, remove dust / dirt or other feculence
2) The scour must be the solvent which was tested, if use IRA / MEK or XYLENE
which didn't demonstrate, the latter's toxicity is stronger and (http://maplered.com) the other two
are better fitting
3) Elementary clean method: First, use the wettish and (http://maplered.com) undepilatory pure-cotton
cloth to clean another clean cloth to clean the feculence before the solvent
volatilization, it should not dry the solvent naturally, lest should feculence
newly on the Material (http://g654.org)
4) For small and (http://maplered.com) deep interface, it needs to clean at full tilt
5) The Material (http://g654.org) that was cleaned out should do with using lacquer, otherwise it should be cleaned out again. If cleaned surface exposed or in the feculence, it should be cleaned again
6) It should be changed the white cloth, which was contaminative, and (http://maplered.com) it should be raved about the impregnant from the container onto the clean cloth and (http://maplered.com) it should not put the cloth into container, otherwise the clean impregnant will be contaminative, it will affect the result
7) It due to all the cleanout liquid are the tinder and (http://maplered.com) have toxicity, it should have good airiness condition / strictly prohibit fireworks when using them, and (http://maplered.com) adopt necessary safe system
Sealant construction process:
Common request:
1) Silicone sealant should be used in 5-40 Celsius degree, this can bring the better effect
2) It can stick on temporary protect adhesive tape when it's necessary, if it use the bottom-gelatinise, it must before using the sealant
3) Using the sealant should be continual, making the sealant form the columned pile out, sealant should pile out equally, make sure it full of sealant on the place where it need, avoid making the bubble
4) It must be decorate after using sealant, the common method is using the tools to make overflow sealant in the direction of interface, and (http://maplered.com) then beauty the interface, make sure the interface contact equally, and (http://maplered.com) then uncover all the temporary protect adhesive tape
5) After 48 hours of using the sealant, the interface can't have the big displacement, otherwise it will effect the result
Executive stand (http://maplered.com) ard:
GB/T 14683-1993
Packing:
24 cartridges/carton
